Internal Floating Roof Systems: Components And Documents
An internal floating roof is a working assembly of parts, and an inspection that names only the deck has not described the system. Each element - the deck skin and its buoyant compartments, the primary and secondary rim seals, the support legs, the anti-rotation guide, bleeder vents, deck drains and the bonding path - carries its own failure mode and its own proving record. The question for a maintenance engineer is coverage: for every component that can be present, which drawing, certificate, test report or inspection entry shows that it was specified, installed and remains fit for service. With no floating-roof product data in the reviewed documentation and no such project in either ledger, that map is built from the governing design basis and the responsible designer, and every missing input is named and owned.
Introduction
This article treats an internal floating roof as an assembly of separate parts whose presence has to be proven by records, not inferred from a drawing of the deck alone. The moving deck follows the liquid level; the outer cover above it is stationary, and an aluminum geodesic dome is one documented form of that fixed cover, never the deck itself. Coverage is the question here: for each component that can be fitted, which drawing, material certificate, test report or inspection entry shows that it was specified, installed and remains acceptable. Deck skin and buoyant compartments, primary and secondary rim seals, legs, guides, vents, drains and bonding are treated as individual lines, each with its own failure mode and proving record. The reviewed company documentation carries no floating-roof component data and neither ledger records such a project, so no parts list, dimension, seal type or standard clause is quoted as authoritative; any absent value is an input the owner or the responsible designer must supply.
System components and their functions
A floating deck is a system, not a single fabricated plate. Around the buoyant deck sit the rim seals that close the annular gap to the shell, support legs that set the low operating position, an anti-rotation device that stops the deck turning, bleeder vents and deck drains that manage vapor and liquid, and a bonding path that ties the deck electrically to the shell. Each is a separate procurement and inspection item with its own drawings and its own acceptance record. A specification that names only the deck leaves the rest of the system undefined.
The inspection question is coverage: for every function the system must perform, is there a named part, and for every named part, is there a record that proves it? That pairing is the component-to-document map. It separates a document that proves a part was specified from one that proves it was installed and one that shows its condition in service. Where the reviewed company documentation holds no floating-roof component data, the map cannot be filled from a catalogue; it is assembled from the governing design basis, the responsible designer's schedule and the owner's inspection plan.
· Deck skin and buoyant compartments - the surface that follows the liquid level.
· Primary and secondary rim seals - the annular gap closure at the shell.
· Legs, guide and anti-rotation fittings - the travel and position controls.
· Vents, drains and bonding - the pressure, liquid and static paths.
Deck, pontoons and buoyancy compartments
The deck may rest broadly on the liquid or be buoyed by discrete sealed pontoon compartments; the choice is a design output, not a property the inspector may assume. A full-contact arrangement presents a continuous underside to the product, while a pontoon arrangement carries a vapor gap beneath part of the skin. The governing design basis fixes which arrangement applies, the buoyancy basis and the compartment layout. What the inspector needs is the arrangement drawing and the compartment schedule that identifies each sealed cell, because a single cell that loses buoyancy changes the deck's trim.
Compartment tightness is a verification item, not a visible feature of the finished deck. The record to request is a compartment identification list tied to the fabrication drawing, the shop tightness or leak test record for each cell, and the in-service inspection entry that confirms no cell has taken on liquid. No buoyancy factor, plate thickness or compartment count is quoted here; those are set by the governing design basis and the responsible designer. Where a cell is found flooded, the responsible designer decides whether the deck may remain in service pending repair.
Primary and secondary rim seals
The annular gap between the deck perimeter and the shell is closed by rim seals, commonly arranged as a primary seal with a secondary seal above it. The primary seal follows the shell at the liquid region; the secondary seal adds a further restriction to vapor movement from the rim space. The existence, type and material of each seal are fixed by the stored product, the shell condition and the governing design basis - three inputs the owner supplies. No seal type, compound or dimension is quoted here as authoritative.
For inspection, the useful records are separate from the seals themselves: a seal schedule naming primary and secondary positions, material compatibility data for the elastomer or fabric in contact with the product, the shell roundness survey that the seal must accommodate, and the gap inspection record taken after installation and at scheduled outages. A reviewer should also ask how seal wear is recorded in service, because a seal that meets a shop test can still be damaged by a shell irregularity or by deck travel.
Support legs and anti-rotation devices
Support legs hold the deck at a set low position when the tank is emptied, keeping the underside clear of the floor and its fittings and leaving room for inspection and cleaning. They are adjustable so that the landing position can be set against the measured floor level and the nozzle and drain elevations, which rarely match the drawing exactly. The leg schedule should state each leg position, its adjustment range and the setting recorded at commissioning; the drawing alone does not prove the as-built setting.
An anti-rotation device restrains the deck from turning about its vertical axis as liquid swirls during filling and withdrawal. Without it, the deck can rotate, twist its seals, foul a leg or guide, and pull the bonding connections out of alignment. The device is a guide arrangement whose design follows the tank geometry and the operating cycle. Its proving record is the guide alignment survey and the travel test that shows the deck rising and falling without binding or rotation across the full operating range.
· Leg count, position and identification against the general-arrangement drawing.
· As-built leg setting and adjustment range recorded at commissioning.
· Anti-rotation guide alignment and full-travel movement record.
· Shell and guide clearance survey at the top and bottom of travel.
Bleeder vents and deck drains
A bleeder vent relieves vapor that accumulates beneath the deck during filling, so the deck is not lifted on a trapped pocket and the vapor space can equalize as the level changes. Its need, size and setting follow the product vapor pressure, the filling rate and the governing design basis; where the design does not require one, the schedule should say so rather than leave the reader to assume. Deck drains remove liquid that collects on the upper surface of the deck, so standing liquid does not add unplanned load or mask a leak.
The records to request are a vent and drain schedule with each item located on the deck plan, the operating description that states when a vent is open or closed, and an inspection entry confirming that drains are clear and that any screening element is intact. Where a drain routes product or vapor, the responsible designer must confirm the destination and the isolation arrangement; that is a process-interface question, not a deck-fabrication detail.
Bonding cables and grounding points
A metallic floating deck inside a hydrocarbon tank must be electrically bonded to the shell so that static charge cannot accumulate on a part that moves relative to its surroundings. Bonding cables or straps span the moving gap between deck and shell, and grounding points tie the assembly into the site's earthing and lightning protection design. The number, routing and resistance criterion are not deck-fabrication choices: they follow the stored product classification, the site lightning study and the governing design basis, all of which the owner supplies.
The documentary test is continuity, not appearance. Request a bonding schedule showing each cable, its attachment points at both ends and its slack allowance across the full travel range; a continuity record taken at handover; and the periodic re-test entry that confirms a cable has not frayed or been disconnected during maintenance. Because the cables move with the deck, a record that is valid at one level does not prove the connection at another. No resistance value or cable count is quoted here as authoritative.
Component documents and inspection records
Documents fall into three groups and an inspector should keep them separate. Design documents - the general arrangement, the component schedule and the governing design basis - show what was intended. Fabrication and supply documents - material certificates, compartment test records, seal material data and factory inspection entries - show what was made. Installation and service documents - alignment surveys, continuity records, travel tests and outage inspection entries - show what was installed and how it is holding up. A complete handover pack carries all three, each with an issue stage and a named custodian.
Public tender documentation reviewed for this topic listed third-party component test reports among the qualification documents required of suppliers. That is an observation about what a buyer may ask for, not a statement that any certificate is held by the company described in the reviewed documentation. For the inspector, the practical use is to classify each requested report by the component it proves and the party that issues it, so a missing record is visible before an outage closes rather than discovered afterwards.
An IFR component-and-document checklist
A checklist is the working form of the map. Each line names a component, the function it performs, the document that proves it was specified, the record that proves it was installed and the in-service inspection entry that keeps it current. Where a line cannot be completed, the gap is recorded with an owner and a due date rather than marked with a placeholder. The checklist is issued at enquiry stage, updated at handover and reused at each turnaround, so the same coverage test is applied every time the tank is opened.
Used this way, the checklist protects against two common failures: a component that exists on the drawing but has no proving record, and a record that exists in the file but maps to no identifiable part. It also gives a maintenance engineer a fixed basis for deciding what to inspect during a short outage. The responsible designer approves the component schedule and the acceptance basis, the owner accepts the pack, and no one needs to assume a dimension, seal type or standard clause to make the coverage check work.
IFR Component Groups And The Records That Prove Each
Component Group | Function In Service | Governing Design Input | Record That Proves It |
Deck skin and buoyant compartments | Follows the liquid level and bounds the vapor space | Arrangement type, buoyancy basis and product density | Compartment schedule and shop tightness test records |
Primary rim seal | Restricts vapor movement at the deck-to-shell annulus | Stored product, shell roundness and travel range | Seal material data and annular gap inspection entry |
Secondary rim seal | Adds a further restriction above the primary seal | Vapor-control obligation and governing design basis | Seal position schedule and post-installation survey |
Support legs | Set the low landing position and floor clearance | Floor level, nozzle elevations and drain positions | Leg setting record taken at commissioning |
Anti-rotation device | Stops the deck turning during filling and withdrawal | Tank geometry, guide layout and operating cycle | Guide alignment survey and full-travel movement record |
Bleeder vents | Equalize vapor beneath the deck as the level changes | Product vapor pressure and filling rate | Vent schedule and operating-state description |
Deck drains | Remove liquid collected on the deck upper surface | Drain routing and isolation arrangement | Drain clearance inspection entry |
Bonding cables and grounding points | Equalize static charge between deck and shell | Product classification and site lightning study | Continuity record and periodic re-test entries |
A Component-And-Document Inspection Checklist
Checklist Line | Item To Confirm | Record To Open | Acceptance Hold Point |
Deck arrangement | Full-contact or pontoon layout matches the approved drawing | General-arrangement drawing and compartment list | Before fabrication release |
Compartment tightness | Each sealed cell identified and accepted | Shop tightness or leak test record per cell | Factory inspection |
Seal pairing | Primary and secondary positions and materials stated | Seal schedule and material compatibility data | Before seal installation |
Leg setting | As-built landing height recorded against floor survey | Commissioning leg setting record | Handover |
Travel and rotation | Deck moves through full range without binding | Guide alignment and travel test record | Handover |
Vent and drain state | Each item located and operating state described | Vent and drain schedule | Design-basis review |
Bonding continuity | Cable routing, slack and continuity verified | Continuity record and re-test plan | Before service and each turnaround |
Document pack | Design, factory and site records separated with owners | Handover document matrix | Acceptance of the whole system |
Evidence Basis And Verification Status
The technical basis is the manufacturer-stated corporate fact base and product sheets, which describe aluminum geodesic dome roofs as fixed outer covers with stated design bases, plus four search-result samples from 14 November 2026. Certificates, specification originals and full standard texts were not independently reviewed. Those sources contain no floating-roof component data, and neither ledger records such a project, so no project record or volume is cited. Public tender notices among those samples listed component test reports, which indicates what a buyer may request, not that any certificate is held. Missing inputs - arrangement type, buoyancy basis, seal compounds and dimensions, vent and drain settings, bonding counts, the governing design-basis edition and the named responsible designer - are identified as owner or designer inputs rather than filled in.
No internal floating roof project appears in the company project ledger. A component-and-document checklist is used instead.
About Center Enamel
Center Enamel (Shijiazhuang Zhengzhong Technology Co., Ltd.) is a manufacturer of bolted storage tanks, factory-applied coatings, aluminum geodesic dome roofs and tank covers. According to the company's own corporate and product documentation, its stated scope covers engineering design, fabrication, in-house quality control and installation support. Every company figure in this article is manufacturer-stated; certificates, specification originals and full standard texts were not independently reviewed for this article.
Frequently Asked Questions
What is the purpose of a secondary rim seal?
A secondary rim seal sits above the primary seal and adds a further restriction to vapor movement through the annular space at the deck perimeter. Its need is set by the vapor-control obligation and the governing design basis, not by a generic parts list. Most importantly, the primary and secondary positions should appear as separate lines on the seal schedule so both can be inspected independently.
Why are support legs adjustable?
Support legs are adjustable so the deck's low landing position can be set against the measured floor level, nozzle elevations and drain positions rather than drawing dimensions alone. The setting is a commissioning record: request the as-built leg height and adjustment range for each leg, because that record proves the deck clears the floor and its fittings when the tank is emptied.
What does an anti-rotation device prevent?
It prevents the deck from rotating about its vertical axis as liquid swirls during filling and withdrawal. Unrestrained rotation can twist the rim seals, foul a leg or guide and pull the bonding cables out of alignment. The verification is a guide alignment survey plus a travel test showing smooth movement through the full operating range without binding.
Is a bleeder vent needed on the deck?
That is a design decision, not a default. A bleeder vent equalizes vapor beneath the deck during filling so the deck is not lifted on a trapped pocket; whether one is fitted follows product vapor pressure, filling rate and the governing design basis. Where none is required, the component schedule should state the omission explicitly rather than leave it to be assumed.
How many bonding points are required?
No count is quoted here. The number, routing and resistance criterion follow the stored product classification, the site lightning protection study and the governing design basis. Ask for a bonding schedule showing each cable and its attachment points at both ends, then a continuity record measured with the deck at more than one travel position.
Are seal materials specified by the stored product?
Yes, compatibility with the stored product is a governing input for the seal compound, along with shell condition and the operating temperature range. Request material data or certificates for the elastomer or fabric in contact with the product and cross-check them against the owner's product data sheet. No seal compound or dimension is specified here.
Which component records are issued at handover?
Expect design documents, fabrication records and installation records as three separate groups: the arrangement drawing and component schedule, material certificates and compartment test reports, and alignment surveys, travel tests, continuity records and the first outage inspection entries. Each should carry an issue stage and a named custodian so a later reviewer can trace any line back to its source.
Does the company source list IFR components?
No. The reviewed corporate fact base and product sheets describe aluminum geodesic dome roofs - fixed outer covers - and their ancillaries; they contain no floating-roof component data, and neither project ledger records such a project. The component list here is a conditional framework drawn from the governing design basis and the responsible designer, not a company product description.
Can a single failed compartment be tolerated?
That is a decision for the responsible designer against the governing design basis, not for an inspector to assume. A flooded cell changes deck trim and buoyancy, so the compartment schedule and the shop test record for each cell must be on file. Where a cell is found flooded, operation continues only if the designer confirms the arrangement remains acceptable pending repair.
Who approves the component schedule?
The responsible designer approves the component schedule and the acceptance basis against the governing design basis, and the owner accepts the completed handover pack. The supplier supplies the fabrication and test records. Keeping those roles distinct matters because a drawing that lists a component does not by itself prove the part was installed or accepted.
Conclusion
A floating deck is an assembly, and an assembly is only inspectable when each part is tied to the record that proves it. The map built here pairs the deck and its compartments, primary and secondary seals, legs, anti-rotation guide, vents, drains and bonding path with the design, factory and site documents that demonstrate specification, installation and continuing condition. Because the reviewed company documentation contains no floating-roof component data and no project record, the map quotes no dimension, seal type or standard clause as authoritative; those belong to the governing design basis and the responsible designer. Turning the map into a checklist with an owner and a hold point for every line is what makes coverage visible before an outage closes. The result is not a claim about any supplied product but a repeatable method an inspection engineer can apply to whatever arrangement the design basis defines.
Talk To Our Engineering Team
Send the stored medium, duty conditions, required capacity and site constraints to the engineering desk. We will return the specification inputs, the document pack to request and the acceptance checks to write into the enquiry. If a different tank type or cover is the better answer, we will say so before you issue the tender.